Thursday, August 11, 2011

Miss-Fits and other Size Issues

I wanted to start off with a mention for my new home http://www.greatwaraviation.com/forum/index.php .  There are some amazing builds and a lot of great advice to be found there.

I have had some fit issues with the Nieuport;

You can see tow things here; my altimeter is much too large and the internal frame is not fitting into its slot on the port side.
2011_0808Image00172011_0808Image0015
I centered the instrument and was able to better center the frame.  I have learned that the frame and the control stick should actually be up against the seat.  This will have to be corrected in the next model.

2011_0808Image00212011_0808Image0010
I have started to make new instruments.  These are out of regular sprue and are about a third the size.  This should be a better fit.

2011_0809Image00052011_0809Image0002
After much sanding; there is still a slightly visible seam.  The flash makes it look much more prominent then it truly is.  I have tried a thin coat of Future to see if that is enough to cover the flaws.  If it isn't then I will go back to another round of sanding.

2011_0809Image0018
These are the turnbuckles for the landing wires.  The turnbuckles are 4mm lengths and the stays are 1mm.

2011_0809Image0042
2011_0809Image0011
I am using 4mm stays on the flying wires and 1mm stays on the landing wires.

2011_0809Image0041
I have attached the first horns to the tail plane.  These are also 1mm cable stays.

2011_0809Image0039
You can see several bubbles in the decals.  I have used several rounds of Solu-Set but they won't go away.  The poor quality decals have been the only disappointment with this kit.  I am hoping that between finish and weathering I can make these disappear.

Tuesday, August 2, 2011

Cockpit Overkill!

So how much detail is too much?  I am starting to think that I have gotten carried away with a cockpit that is barely visible at best.  I finished the internal rigging and ran control lines.  I just think that maybe I am spending too much time on stuff that won't be seen.  It is fun though and in the end that is why I do this.

2011_0802Image00012011_0802Image0004
I decided to open up the brass chute.  I first drilled some small guide holes then went after it with my Dremel.  I know these were open; but I think in the future painting will be adequate.

2011_0802Image00022011_0802Image0003
I went with the rigging over the throttle after all.  It wasn't hard getting the piece off, but I liked it better lying flat against the fuselage.  I attached some line to the control stick for a rudder cable.  I think the placement of my pulley was too high.  Here you can also see the start of the rudder control assembly.

2011_0802Image0005
This is a better shot of the rudder control; I added foot loops and drilled small (0.3mm) holes into the ends for the wires.  My lines are again 2lb Maxima Chameleon line colored silver.  I attached this with a small drop of thin CA.  Many thanks again to Des at http://www.ww1aircraftmodels.com/ his recommendation of using thin CA for rigging and small details has been a real game changer for me.  It runs right into the little gaps and sets up nice and fast to hold where you want.

2011_0802Image0009
2011_0802Image0008
2011_0802Image0007
2011_0802Image0006
These are shots of my half completed cockpit.  You can see that I ran the control wires all the way through the fuselage.  I think I will change my mind on this and cut them off in the third box section.  I am unhappy with my control stick.  I liked the last one I did better (kind of like the seat cushion).  I think I need some smaller brass rod to make this look good.  I also want to put bends in the cross pieces to connect them (visually) with the aileron controls.  Not too bad for a couple hours work.  I am still not an artist like Des or most of the guys (and gals) at the http://www.theaerodrome.com/forum/ but I am getting better with each project.

Monday, August 1, 2011

Horns and Pullies

I have started adding eyelets for my rigging on the wings, and begun the interior rigging in the cockpit as well.  I tried to create a pully system for the rudder cables.

2011_0801Image0016
Here is the interior rigging on the starboard side.  I added the cable behind the seat as well since area was visible in my last model.

2011_0801Image0019
I started making a pully using some larger diameter sprue and a hole-punch on some brass sheet.  It looked good but was much too large.  I ended up with a small bit of an air release tab and a much smaller piece of brass.  I drilled a 0.5mm hole through everying and then used a broken bit of a 0.3mm drill bit as an axel.  It doesn't look as nice; but I think the size is much closer.

2011_0801Image0022
I used a drop of CA to mount this in the front of the cockpit.  I know it isn't centered; but since I build the interior into the starboard side it will make things easier to rig.


This is another discovery; rigging holes in the horns.  Once again I am not certain if I didn't notice these before or if they are just missing from the Academy molding.  I drilled the holes through with a 0.3mm drill bit to prepare these for rigging.

2011_0801Image0014
Here are the control horns with cableing attached.  I used my standard 2lb line colored silver with a Sharpie marker.  I plan on adding turnbuckles to these lines so I just left each with a 3 inch tail.  I hope this will give me enough to work with.

2011_0801Image0024
I added the throtle control to the port side interior.  I did want to have it inside of the rigging so I put it in first.  Now that I look at it; I think I want the rigging to pass under the throtle control.  This may pose some problems.  I still have to rig the port side interior then start putting the interior parts together.

I am trying to decide if I want the control cable to run all the way through the fuselage or just have them end under the seat...  I will have to decide before I complete the interior so you should know by my next posting.

Wednesday, July 27, 2011

A Second Try at Details

I have to start off with a correction and a recommendation.  I mentioned a couple months ago that I ordered photoetch instrument bezels from AeroClub and was sent 1:72 instead of 1:32.  I decided that it was important to me to get the right parts so I emailed John.  I was willing to pay for shipping and to return the 1:72 bezels; but he said no and sent me the correct part right away.  If you are even considering build WWI aircraft (or WWII for that matter) I strongly encourage you to pick up these extras.  You will not regret it!

2011_0727Image0016
So here are my Airscale instrument decals and my AeroClub bezels.  The decals are very accurate, but since this will be hanging from my sons ceiling I have gone for looks over accuracy.

2011_0727Image0012
These were trimmed off some sprue from my extras box.  I believe they are the air release holes but they are nicely oversized compared to the rest of the sprue.

2011_0727Image0014
I sanded the rough spots and brush painted with Tamiya X31 Titanium Gold.  This is the Wingnut wings recommendation for brass parts.  When the paint was dried I airbrushed on some Future to prepare for decals.

 2011_0727Image0018
So here they are more or less finished.  Only one decal is actually an altimeter and it is German.  But they look good.  I did tweak the decal on the right as I was adding the bezel but that is why I did two.  I have also added some Future to act as the instrument glass.  Overall I am very happy with the results.

2011_0727Image0013
I am not sure if you can tell; but I did a wash of Vallejo Oily Steel on the engine.  Mostly I am including another shot here because I am so damn happy with how it turned out! >grin<  While I am a huge fan of Tamiya paints especially when airbrushing; I really love Vallejo paints for brushwork and washes.  I just wish I had a local source for more of these.

2011_0727Image00012011_0727Image0002
I am not so proud of this wood grain.  I read of some people using acrylics for the wood grain and thought to give it a try.  I was not pleased.  I went back with oils, but the clean-up from the acrylics did more damage to my base coat then I realized.

2011_0727Image00062011_0727Image0004
I am happy with the wood grain on the propeller.  I still have no idea how some manage a two tone effect here, but I will figure that one out...  The picture on the right also shows where I had to fill in the sinkholes.
2011_0727Image00032011_0727Image0032
I went with a darker wood grain on the spars this time.  I am much happier with this effect.  I again did the lead foil wraps instead of using the decals that come with the kit.  I think the substance of the lead foil just adds a more realism.

2011_0727Image00262011_0727Image0021
Here is my seat.  I have noticed that the belts on all the kits seem very wide.  I think I over did the effect here but I will work on this with future models.  The seat cushion turned out well.  I did a leather color XF52 Flat Earth (again from the Wingnut directions) then I dipped it in the same wash that I used on the engine.  Finally I did a drybrush of Red Brown XF64 to finish it off and a little Future to protect it. 
I took a great deal more care with the wheels on this project.  They were pretty much just thrown on the last plane.  I airbrushed the centers then brushed XF69 Nato Black for the rubber (Wingnut Wings again).   Its funny how you can be perfectly happy with Flat Black for tires until you see something that is better.  WOW again I am amazed out how a little color change can make such a huge difference.

The heat wave has come to an end so I will probably be crawling out of the basement and tackling my honey-dos for a while.  Hopefully this will give me some time for my 0.4mm brass tube to come in.

Sunday, July 24, 2011

Rotary Redux

I took some extra time cleaning up the interior.  Since I will be adding the internal rigging I don't need the mold lines.
2011_0724Image00052011_0724Image0003

I made an interesting discovery; I don't know if it because this is an older molding or if I just didn't notice it on the Academy model but there are marking for the holes in the seat back.  Of course I had to make use of them.
2011_0724Image00092011_0724Image0014

My seat cushion isn't looking as nice this time.  I hope that after painting and remembering to add a seat belt it will still look good.
2011_0724Image0027

I jumped ahead to the engine.  I felt inspired after reading the instructions for my Sopwith Pup from Wingnut Wings.  They use a bit more color on their engine so I thought I would give it a try.  This is the biggest difference; the copper exhaust.
2011_0724Image0037

I don't know if it is appropriate for a Nieuport but I like the way it looks.  I also thought I would give spark plug wires a try this time.  I colored my rigging line (2lb fishing line) black with a Sharpie and attached it with CA.  I actually dipped the line into the CA and then as I held it in place ran a drop of accelerator down the line help it stick.
2011_0724Image0033

Here are a couple shots of the finished product.  I am really surprised what a difference a little color and some fishing line can make.
2011_0724Image0038
2011_0724Image0040

Finding the markings on the seat back was a nice surprise; finding sinkholes in the propeller wasn't.  So I will fill and sand and fill and sand then maybe I will do some wood grain...